-SET OF TEN WHEEL STUDS.-These are often required when adding wheel spacers or with certain rims. Meets or exceeds OEM specs! MADE IN THE USA!-Fits all 1982, 1983, 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 19..
-SET OF 16 STUDS: These wheel studs fit most 1998-2012 Polaris Quads and may fit other years and makes as well. They are 1/2" longer than Polaris parts numbers 7515513, 7515523.-1/2" longer than stock for quads with 7515513, 7515523 wheel studs-The s..
-Made by Muzzys and uses the same Delphi/Packard connectors, terminals, and seals as the factory wiring harness using the factory correct cross linked polyethelene high temperature TXL wire in the proper gauge.-Includes TWO Sockets and FOUR High Qual..
-(Set of FOUR caps) Muzzys Inflate Through High Pressure Valve Stem Caps-Made in the USA! Commonly used for Commercial trucks, RV's, Trailers and Semi's but can used on anything with a valve stem.-Valve has two seals and is protected by a solid, all ..
-(Set of FOUR valve stems) Please verify fitment of this valve stem kit before ordering.-To install pull new VS-90 into valve hole, slide the sensor onto the metal key at the base of the stem. It will lock in place.-It is effortlessly removed by push..
-SET OF FOUR KITS: Includes valve stem, screw, and cap as pictured. THIS IS NOT A TPMS SENSOR, JUST A VALVE STEM FOR THE SENSOR.-Fits 2014 and Newer Dodge RAM 1500 2500 3500 and Jeep Cherokees-Please verify fitment of this valve stem kit before order..
- Make sure this fitsby entering your model number.- Muzzys Texas State Flag Emblem. Measures about 3.5 in wide, 3.5 in tall, sits raised 0.2 in.- Car wash safe, sun resistant, will last years on your truck!- Made in the USA by Muzzys from high qual..
-Replace your boring TPMS nuts with these awesome high quality black and silver nuts.-These nuts replace the nuts in the following TPMS rebuild kits: Xtra Seal 17-20206ak, Dill 1090k, 2000k, 1096, Schrader 20023, 20036-Integrated silver plastic washe..
-Fits any vehicle that uses a TPMS nut-High quality black anodized finish-Integrated black plastic washer to protect your rim from gouging-Made of aluminum-Made in the USAHave black rims but can't find black tire pressure sensor nuts to match? We hav..
-Made by Muzzys and uses the same Delphi/Packard connectors, terminals, and seals as the factory wiring harness using the factory correct cross linked polyethelene high temperature TXL wire in the proper gauge.-High Quality Nylon Splices Included-Hea..
-For Use With: 8mm (5/16") ID (inner diameter) hose. Valve can safely be used with water, fuel, gas, diesel, and oils.-Includes: (ONE) check valve and (TWO) high quality stainless steel smooth edge band clamps that will not cut into your hoses-Valve ..
- Make sure this fitsby entering your model number.- Fits all 1" Rubber TPMS valve stems which is the industry standard size for most makes and models.- Includes FOUR caps and FOUR sleeves made from high quality corrosion resistant and treated mater..
- Make sure this fitsby entering your model number.- Fits all 1" Rubber TPMS valve stems which is the industry standard size for most makes and models.- Includes FOUR caps and FOUR sleeves made from high quality corrosion resistant and treated mater..
-GM LS / LT Swap (Gen III, IV, V), Adapts TH350, TH400, 700R4-Used on various LS Swaps and Conversions-Fits Gen III/IV LS and Gen V LT series engines-Not required on 1999-2000 6.0L stock flexplate (longer crank with flat flexplate)-Inserts into rear ..
-Replaces: ACDelco PT2298, 1P1032, 236, 1006-311094, S-553, 57-4540, 311094, 85855, PT120-Made in the USA by Muzzys using OEM high temp wire, OEM Delphi-Packard connectors, pins, and seals to ensure a secure, long lasting, moisture free connection.-F..
-Back Up Reverse Lockout Pigtail For GM T56 Transmissions including LT1 and LS1 Applications.-Made by Muzzys and uses the same Delphi/Packard connectors, terminals, and seals as the factory wiring harness using the factory correct cross linked polyet..