abn extractor de cables de bujías e instalación para volkswagen y audi, herramienta de extracción de cables de herramientas de bujías vw, herramienta de cables de bujías
- Marca:
abn
- Código producto: B07GQ4WJXV
- Disponibilidad: Traemos a pedido, tiempo de 15 a 25 dias.
-
$CLP 28.527
TÉRMINOS Y CONDICIONES
------------------------------------------
- El producto se trae a pedido, en un transcurso de 15 a 25 dias, si alguna restriccion de un ente gubernamental o de salud publica cambia o restringe vuelos, los pedidos pueden demorar mas tiempo.- Precios pueden cambiar previo aviso. Depende de precio con proveedores o existencia.
- Fotos referenciales del producto, consulte no mas
- Despachamos a todo Chile con Starken.
- Productos importados de Estados Unidos, es probable que los productos electronicos trabajen en 110V y NO en 220V, podria usar un transformador, para mas informacion primero nos puedes preguntar todas las inquietudes que tengas.
-GET THE JOB DONE: The ABN | Spark Plug Wire Remover Tool makes changing spark plug connectors possible without removing the intake manifold or any fuel lines and rails; Easily fits on the end of the rubber boot to unlock/lock the boot and properly remove the plug wire without damage
-FITS YOUR VEHICLE: For Volkswagen and Audi vehicles with standard prong plug caps on each side (not recommended for non-VW/Audi plug leads); Volkswagen ? New Beetle 2.0 engine AZJ (AEG), Golf IV & V 1.6 engine (AVH), 1993-2005 2.0L 4 cylinder (AZG), 1998-2006 1.8L 4 cylinder (BBW), 2006 and later 2.0L 4 cylinder turbo (BDC); Audi ? 1998-2006 1.8L 4 cylinder turbo (BEV), 2006 and later 2.0L 4 cylinder turbo (BGD)
-ACCESS DEEP SPARK PLUGS: Angled shaft allows access to deep plugs in hard-to-reach areas; 12.6-inch (32cm) overall length; 3.75? x 0.4? x 1.2? inch (9.5cm x 1cm x 3cm) handle, 9.25-inch (23.5cm) shaft, 2.2-inch x 0.8-inch (5.6cm x 2cm) boot end
-EASY TO USE: No need to remove the intake ? Simply push the spark plug boot removal tool down, turn, and pull; Perform spark plug change when engine is cold to prevent the heads from stripping; After pulling the plugs, we recommend applying lubrication to make the job easier; When installing wires, refrain from pushing too hard without the tabs aligned on the tool to prevent the boot end from spreading and getting stuck
-BUILT TO LAST: Handle constructed from hard plastic for comfort, less user fatigue, and more productivity; Shaft and boot end constructed from stainless-steel for maximum strength and longevity
Save yourself from the frustration of trying to seat and unplug spark plug wires from poorly designed cars and instead use the ABN | Spark Plug Boot Puller. It makes it possible to change spark plug connectors without removing the intake manifold or any fuel lines and rails. Simply push the spark plug remover tool down, turn, and pull. This spark plug puller tool has an angled shaft to reach deep plugs on newer Volkswagen Beetle models and cars with 2.0 engines. It is suitable for VW Golf IV & V with 1.6 engine AZJ locking, VW, Audi, Bora, Mercedes, Smart, and other Volkswagen and Audi vehicles with similar engines. We recommend changing spark plugs when the engine is cold and applying lubrication (not included) to make the job easier. Not recommended for non-VW/Audi plug leads. WARNING: This product can expose you to chemicals which is [are] known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
-FITS YOUR VEHICLE: For Volkswagen and Audi vehicles with standard prong plug caps on each side (not recommended for non-VW/Audi plug leads); Volkswagen ? New Beetle 2.0 engine AZJ (AEG), Golf IV & V 1.6 engine (AVH), 1993-2005 2.0L 4 cylinder (AZG), 1998-2006 1.8L 4 cylinder (BBW), 2006 and later 2.0L 4 cylinder turbo (BDC); Audi ? 1998-2006 1.8L 4 cylinder turbo (BEV), 2006 and later 2.0L 4 cylinder turbo (BGD)
-ACCESS DEEP SPARK PLUGS: Angled shaft allows access to deep plugs in hard-to-reach areas; 12.6-inch (32cm) overall length; 3.75? x 0.4? x 1.2? inch (9.5cm x 1cm x 3cm) handle, 9.25-inch (23.5cm) shaft, 2.2-inch x 0.8-inch (5.6cm x 2cm) boot end
-EASY TO USE: No need to remove the intake ? Simply push the spark plug boot removal tool down, turn, and pull; Perform spark plug change when engine is cold to prevent the heads from stripping; After pulling the plugs, we recommend applying lubrication to make the job easier; When installing wires, refrain from pushing too hard without the tabs aligned on the tool to prevent the boot end from spreading and getting stuck
-BUILT TO LAST: Handle constructed from hard plastic for comfort, less user fatigue, and more productivity; Shaft and boot end constructed from stainless-steel for maximum strength and longevity
Save yourself from the frustration of trying to seat and unplug spark plug wires from poorly designed cars and instead use the ABN | Spark Plug Boot Puller. It makes it possible to change spark plug connectors without removing the intake manifold or any fuel lines and rails. Simply push the spark plug remover tool down, turn, and pull. This spark plug puller tool has an angled shaft to reach deep plugs on newer Volkswagen Beetle models and cars with 2.0 engines. It is suitable for VW Golf IV & V with 1.6 engine AZJ locking, VW, Audi, Bora, Mercedes, Smart, and other Volkswagen and Audi vehicles with similar engines. We recommend changing spark plugs when the engine is cold and applying lubrication (not included) to make the job easier. Not recommended for non-VW/Audi plug leads. WARNING: This product can expose you to chemicals which is [are] known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
