e6013 - acero dulce / de uso general - electrodo / varilla de soldadura - 14 "x 1/8"
- Marca:
tgb
- Código producto: B07CX6YSRQ
- Disponibilidad: Traemos a pedido, tiempo de 15 a 25 dias.
-
$CLP 259.872
TÉRMINOS Y CONDICIONES
------------------------------------------
- El producto se trae a pedido, en un transcurso de 15 a 25 dias, si alguna restriccion de un ente gubernamental o de salud publica cambia o restringe vuelos, los pedidos pueden demorar mas tiempo.- Precios pueden cambiar previo aviso. Depende de precio con proveedores o existencia.
- Fotos referenciales del producto, consulte no mas
- Despachamos a todo Chile con Starken.
- Productos importados de Estados Unidos, es probable que los productos electronicos trabajen en 110V y NO en 220V, podria usar un transformador, para mas informacion primero nos puedes preguntar todas las inquietudes que tengas.
-All-position, mild steel electrode for welding light to medium-gauge steel. Common uses include tack welding on thin sheet metal such as galvanized sheets, automobile bodies, metal furniture, window frames, fences, storage tanks, farm equipment and iron grills
-Excellent operating characteristics when using small diameter electrodes to weld thin sheet metal using lower open-circuit AC voltage
-One of the easiest electrodes to use because of its easy slag control in vertical down welding, its wide operating range and restrike capabilities
-This electrode has a soft, steady and quiet arc that produces very little smoke or spatter
-Select your Electrode Diameter and Package Quantity from the Options - Check Picture #3 for Welding Parameters.
Instructions: Clean the weld zone of contaminants as well as possible. A small AC machine or DC machine (electrode + reverse polarity or ? straight polarity) can both be used! AC will prevent arc blow, DC+ reverse polarity produces deeper penetrating welds on medium gauge steels and DC- straight polarity on thinner or light gauge steels. Set amperage to the proper range as listed on the product recommended amperage chart. Maintain a short arc length and hold the electrode at a 1- angle and use a slight back and forth whipping motion. If overhead welding, use a straight circular motion. For vertical-down welding, choose amperage in the upper end of the recommended range and use stringer beads or a slight weaving technique keeping the weld puddle in place by pointing the electrode up into the puddle. For vertical-up welding, use amperage settings in the lower end of the recommended range and use the shelf or step method adding layer on top of layer. Do not use whipping motion. Allow the part to air-cool and remove slag with a chipping hammer and brush to a nice finish.
-Excellent operating characteristics when using small diameter electrodes to weld thin sheet metal using lower open-circuit AC voltage
-One of the easiest electrodes to use because of its easy slag control in vertical down welding, its wide operating range and restrike capabilities
-This electrode has a soft, steady and quiet arc that produces very little smoke or spatter
-Select your Electrode Diameter and Package Quantity from the Options - Check Picture #3 for Welding Parameters.
Instructions: Clean the weld zone of contaminants as well as possible. A small AC machine or DC machine (electrode + reverse polarity or ? straight polarity) can both be used! AC will prevent arc blow, DC+ reverse polarity produces deeper penetrating welds on medium gauge steels and DC- straight polarity on thinner or light gauge steels. Set amperage to the proper range as listed on the product recommended amperage chart. Maintain a short arc length and hold the electrode at a 1- angle and use a slight back and forth whipping motion. If overhead welding, use a straight circular motion. For vertical-down welding, choose amperage in the upper end of the recommended range and use stringer beads or a slight weaving technique keeping the weld puddle in place by pointing the electrode up into the puddle. For vertical-up welding, use amperage settings in the lower end of the recommended range and use the shelf or step method adding layer on top of layer. Do not use whipping motion. Allow the part to air-cool and remove slag with a chipping hammer and brush to a nice finish.
