amplificador de audio para automóvil timpano compact de 4 canales tpt1000.4 - 4x 260 vatios a 2 ohmios - estéreo de alta potencia 12 voltios amplificador de clase d de rango completo puenteable

TÉRMINOS Y CONDICIONES

------------------------------------------

- El producto se trae a pedido, en un transcurso de 15 a 25 dias, si alguna restriccion de un ente gubernamental o de salud publica cambia o restringe vuelos, los pedidos pueden demorar mas tiempo.
- Precios pueden cambiar previo aviso. Depende de precio con proveedores o existencia.
- Fotos referenciales del producto, consulte no mas
- Despachamos a todo Chile con Starken.
- Productos importados de Estados Unidos, es probable que los productos electronicos trabajen en 110V y NO en 220V, podria usar un transformador, para mas informacion primero nos puedes preguntar todas las inquietudes que tengas.

-COMPACT DESIGN: Digital class D Brazilian technology allows this amplifier to have a small footprint by integrating a high-speed mosfet power supply with top of line transistors to ensure performance in a small heat sink without compromising performance. Dimensions: 8.11? depth x 8.11? width x 2.60? height
-POWER: This amplifier is designed to run your stereo system with the power it needs to perform! 1200 Watts maximum dynamic RMS power output of 4x 300 Watts at 2 Ohms per channel. Its high efficiency rate of 84% provides more power with less battery consumption.
-BRIDGEABLE: Double the power output to your speakers by bridging two channels. Minimum impedance of 4 Ohms per bridged channel at output power of 2 x 520 Watts RMS
-TECHNOLOGY: A smart electronic 2-way protection circuit protects the amp if it gets too hot or if speakers fail causing a short! Focusing in sound quality, a full range response of 20 to 26,000Hz was used to give the best sound reproduction on this tiny amplifier.
-FEATURES: Fork terminal connector power and speaker wire Inputs. Built-in crossover filters for easy tuning! Choose between a fixed HPF at 90Hz or LPF at 90Hz or just turn it FLAT and use your external crossover or DSP settings. It also includes Variable Gain Control. Level controls are not for adjusting volume. They adjust the amount of signal that is coming into the amplifier from your signal source.

Number of Channels: 4Max Dynamic Output: 4 x 300 Watts RMS 2 OhmsRMS Power at 2 Ohms 12.6 Volts: 4x 225 Watts RMSRMS Power at 4 Ohms 12.6 Volts: 4x 140 Watts RMSBridged RMS Power at 4 Ohms 12.6 Volts: 2x 450 Watts RMSRMS Power at 2 Ohm 14.4 Volts: 4x 260 Watts RMSRMS Power at 4 Ohm 14.4 Volts: 4x 165 Watts RMSBridged RMS Power at 4 Ohms 14.4 Volts: 2x 520 Watts RMSSupply Voltage: 11 ~ 16VFrequency Response: 20Hz ~ 26KHzCrossover Low Pass: Fixed at 90HzCrossover High Pass: Fixed at 90HzSignal to Noise: > 90 dBHarmonic Distortion: < 0.9 % THDInput Sensitivity: 0.2 VInput Impedance: 14K OhmsImpedance Output: 2 OhmsConsumption with Signal Musical: 4A ~ 50ADimensions (L x W x H): 8.11? x 8.11? x 2.60?Weight: 3.75 LbsBefore Installing:You must follow the instructions for the product?s installation and connections to guarantee optimal performance. Before using the amplifier, always follow these guidelines:? Make sure the amplifier is switched off before adding or removing any connections- Keep all cables as far away as possible from the ignition cables? Always use 100% Cooper cables and good quality connectors.? To avoid damaging the cables, make sure that they do not touch sharp metal edges.Important: Use a 60A fuse 12 inches away from the battery as a safety precautionThe power rated data are based on equipment from the PRV Audio Group laboratory. Frequency reference of 1Khz with THD+N to ?10% in impedances referring to the indicated in each measurement. The electronic components and the manufacturing process can present manufacturing variations. This amplifier is designed to perform on music applications ( with speakers ), any load test ( resistant-load ) is not recommended.