puños malleus de motocicleta mecanizados - para honda - manguito del acelerador y agarre del embrague para barras de 1 "
- Marca:
tj brutal customs
- Código producto: B08L5RC8P3
- Disponibilidad: Traemos a pedido, tiempo de 15 a 25 dias.
-
$CLP 388.955
TÉRMINOS Y CONDICIONES
------------------------------------------
- El producto se trae a pedido, en un transcurso de 15 a 25 dias, si alguna restriccion de un ente gubernamental o de salud publica cambia o restringe vuelos, los pedidos pueden demorar mas tiempo.- Precios pueden cambiar previo aviso. Depende de precio con proveedores o existencia.
- Fotos referenciales del producto, consulte no mas
- Despachamos a todo Chile con Starken.
- Productos importados de Estados Unidos, es probable que los productos electronicos trabajen en 110V y NO en 220V, podria usar un transformador, para mas informacion primero nos puedes preguntar todas las inquietudes que tengas.
-Fits most throttle cables and stock Honda shadow switch housings!
-The simple way to set up your handlebars!
-Machined from 6061 Aluminum
-Anodized with beautiful knurling!
-100% Satisfaction Guarantee. If you are not happy with your choice, contact us for a full refund-
The Malleus Machined Grips for Honda Shadow are the perfect choice for your bobber or chopper build! The throttle sleeve tube fits most throttle cables and stock honda shadow switch housings and the clutch side grip and throttle sleeve tube will work with all 1" handlebars. The Malleus Machined Aluminum Throttle Sleeve and Clutch Grip set is the most simple way to set up your handlebars, no need for grips that will wear out or need replacing! The throttle sleeve and clutch side grip are machined from 6061 Aluminum and anodized with beautiful knurling, not too extreme, just enough to provide a solid hold! I always hated when grips were knurled to the point of aggressively shredding my palms!! Not so with the Malleus Grip Set! The throttle sleeve fits perfectly in our Acerus Throttle Assembly The matching clutch side grip simply slides on and attaches to the handlebar with 3 included #6-32 set screws, we recommend using a bit of red loc-tite on each screw . Some folks like to add a dab of glue when sliding the clutch side grip on, but we have found it's not necessary. The throttle sleeve is meant for single cable operation. It is not meant to run the push cable. You do not need the push cable, remove it and enjoy your newfound throttle performance!! Fits 1" handlebars Fits the following models throttle cables - Honda Rebel Honda Shadow VLX600 / VT600 Honda Shadow VT750, ACE, Aero, Spirit, Phantom, RS Honda Sabre Honda Magna Honda VT1100 Honda VTX *May fit other metric bikes. While this part doesn't need grips, you can leave the clutch side grip off and use a traditional set of rubber grips. A rubber grip set will fit over the throttle sleeve. We recommend using a tiny bit of red thread-locker on the set screws of the clutch side grip.
-The simple way to set up your handlebars!
-Machined from 6061 Aluminum
-Anodized with beautiful knurling!
-100% Satisfaction Guarantee. If you are not happy with your choice, contact us for a full refund-
The Malleus Machined Grips for Honda Shadow are the perfect choice for your bobber or chopper build! The throttle sleeve tube fits most throttle cables and stock honda shadow switch housings and the clutch side grip and throttle sleeve tube will work with all 1" handlebars. The Malleus Machined Aluminum Throttle Sleeve and Clutch Grip set is the most simple way to set up your handlebars, no need for grips that will wear out or need replacing! The throttle sleeve and clutch side grip are machined from 6061 Aluminum and anodized with beautiful knurling, not too extreme, just enough to provide a solid hold! I always hated when grips were knurled to the point of aggressively shredding my palms!! Not so with the Malleus Grip Set! The throttle sleeve fits perfectly in our Acerus Throttle Assembly The matching clutch side grip simply slides on and attaches to the handlebar with 3 included #6-32 set screws, we recommend using a bit of red loc-tite on each screw . Some folks like to add a dab of glue when sliding the clutch side grip on, but we have found it's not necessary. The throttle sleeve is meant for single cable operation. It is not meant to run the push cable. You do not need the push cable, remove it and enjoy your newfound throttle performance!! Fits 1" handlebars Fits the following models throttle cables - Honda Rebel Honda Shadow VLX600 / VT600 Honda Shadow VT750, ACE, Aero, Spirit, Phantom, RS Honda Sabre Honda Magna Honda VT1100 Honda VTX *May fit other metric bikes. While this part doesn't need grips, you can leave the clutch side grip off and use a traditional set of rubber grips. A rubber grip set will fit over the throttle sleeve. We recommend using a tiny bit of red thread-locker on the set screws of the clutch side grip.
